VBET 110302 车削刀片
对比 合适的材料与应用, ，然后选择 a brand 查看 the exact SKUs.
- ISO Code
- VBET110302
- 刀片尺寸
- 110302
- Shape
- V
查找合适的选项
Select the workpiece material and application. 品牌 remains optional.
Brands
该父型号的全部可选规格。
VBET 110302 — 35° rhombic turning insert, 4 edges, 钢, 不锈钢. There are currently 13 variants in stock from Achteck. Measured across the range: 6.35 mm inscribed circle, 3.18 mm thickness, 0.2 mm nose radius.
The designation encodes the geometry: the first letter is the shape (V), the following letter the clearance angle, then the tolerance class, then size, thickness and nose radius. If you want to check any of it, our ISO insert code decoder breaks the full string down character by character.
Geometry and dimensions
| Insert family | VBET |
|---|---|
| Category | 车削刀片 |
| Shape | 35° rhombic (V) |
| Usable cutting edges | 4 |
| 内切圆直径 (IC) | 6.35 mm |
| 厚度 (S) | 3.18 mm |
| 刀尖圆角 (RE) | 0.2 mm |
| Fixing hole diameter (D1) | 2.8 mm |
| Hand | Right, Left |
| Variants in stock | 13 |
| Brands | Achteck |
Recommended cutting data
The figures below are the manufacturers' published ranges, aggregated across the 13 variants listed on this page. The typical column is the median, which is where most shops end up running. Treat the full range as the envelope, not a target — start around 60–70% of it and work up.
| 工件材料 | Cutting speed vc (m/min) | Typical vc | Feed fn (mm/rev) | Depth of cut ap (mm) | Variants with data |
|---|---|---|---|---|---|
| 钢 (P) | 50 – 200 | 50 – 180 | 0.02–0.22 | 0.05–2 | 13 of 13 |
| 不锈钢 (M) | 60 – 150 | 60 – 150 | 0.02–0.22 | 0.05–2 | 3 of 13 |
To turn a cutting speed into a spindle speed for your actual diameter, use the cutting parameters calculator: n = vc × 1000 / (π × D).
Carbide grades available
13 variants of VBET 110302 are stocked in these grades: AT210A, AT210, AP100U.
Across this range the grades specified most often are AT210A, AT210, AP100U. Within one brand's range, a higher middle digit usually means a tougher grade — better on interrupted cuts, slightly less wear resistant. See carbide grades explained for how to read the names.
槽型 geometries
断屑槽 stocked for VBET 110302: Y, F, M.
The chipbreaker sets the usable feed window far more than the depth of cut does. A roughing geometry run at finishing feed will not break the chip; a finishing geometry pushed into a roughing cut will chip. Match it to the feed you will actually run — chipbreaker selection guide.
Typical applications
- 精加工
For more on cutting steel, see our material-specific guide.
Choosing the right VBET 110302
Three things decide which variant you need:
- The workpiece material group. This page lists variants published for 钢, 不锈钢. Pick a grade from the group you are cutting — a steel grade on a superalloy will fail quickly.
- Feed, not depth of cut. The chipbreaker is defined by its feed window. Decide the feed first, then pick the geometry that covers it.
- 刀尖圆角 versus finish. VBET 110302 is stocked here at 0.2 mm. A larger radius gives better finish at the same feed and a stronger edge, but raises cutting force.
Not sure whether VBET 110302 is the right shape at all? The turning insert selection guide compares shapes by what the part profile allows.
Frequently asked questions about VBET 110302
What size insert is VBET 110302?
VBET 110302 has an inscribed circle of 6.35 mm and a thickness of 3.18 mm. As a rule the depth of cut should stay under about two thirds of the inscribed circle.
What nose radius does VBET 110302 have?
The nose radius (the last two digits of the designation) is 0.2 mm on the variants listed here. Surface roughness scales roughly with fn²/(32 × RE), so at a fixed feed a larger radius halves Ra.
Which holder does VBET 110302 fit?
The holder designation must carry the same shape letter (V) and the same size digit. Send us your holder code and we will confirm the match before you order.
How many VBET 110302 variants do you stock?
13 variants from Achteck, listed below with grade, chipbreaker and the published cutting data where the manufacturer provides it.
What cutting speed should I run for VBET 110302?
For 钢, the published range across these variants is 50–200 m/min, with a typical window of 50–180 m/min. Heavy cuts sit at the bottom of that range, light finishing cuts at the top.