TNGG 160404 Turning Inserts
Compare suitable materials and applications, then choose a brand to view the exact SKUs.
- ISO Code
- TNGG160404
- Insert Size
- 160404
- Shape
- T
Find the Right Option
Select the workpiece material and application. Brand remains optional.
Brands
All available options for this parent model.
TNGG 160404 — triangular 60° turning insert, 6 edges, Steel, Stainless steel. There are currently 10 variants in stock from Achteck. Measured across the range: 9.53 mm inscribed circle, 4.76 mm thickness, 0.4 mm nose radius.
The designation encodes the geometry: the first letter is the shape (T), the following letter the clearance angle, then the tolerance class, then size, thickness and nose radius. If you want to check any of it, our ISO insert code decoder breaks the full string down character by character.
Geometry and dimensions
| Insert family | TNGG |
|---|---|
| Category | Turning Inserts |
| Shape | triangular 60° (T) |
| Usable cutting edges | 6 |
| Inscribed circle (IC) | 9.53 mm |
| Thickness (S) | 4.76 mm |
| Nose radius (RE) | 0.4 mm |
| Fixing hole diameter (D1) | 3.81 mm |
| Hand | Neutral, Right, Left |
| Variants in stock | 10 |
| Brands | Achteck |
Recommended cutting data
The figures below are the manufacturers' published ranges, aggregated across the 10 variants listed on this page. The typical column is the median, which is where most shops end up running. Treat the full range as the envelope, not a target — start around 60–70% of it and work up.
| Workpiece material | Cutting speed vc (m/min) | Typical vc | Feed fn (mm/rev) | Depth of cut ap (mm) | Variants with data |
|---|---|---|---|---|---|
| Steel (P) | 50 – 200 | 50 – 180 | 0.05–0.4 | 0.2–4 | 10 of 10 |
| Stainless steel (M) | 60 – 150 | 60 – 150 | 0.08–0.2 | 0.5–2.3 | 1 of 10 |
To turn a cutting speed into a spindle speed for your actual diameter, use the cutting parameters calculator: n = vc × 1000 / (π × D).
Carbide grades available
10 variants of TNGG 160404 are stocked in these grades: AT210, AT210A, AP100U.
Across this range the grades specified most often are AT210, AT210A, AP100U. Within one brand's range, a higher middle digit usually means a tougher grade — better on interrupted cuts, slightly less wear resistant. See carbide grades explained for how to read the names.
Chipbreaker geometries
Chipbreakers stocked for TNGG 160404: H, F.
The chipbreaker sets the usable feed window far more than the depth of cut does. A roughing geometry run at finishing feed will not break the chip; a finishing geometry pushed into a roughing cut will chip. Match it to the feed you will actually run — chipbreaker selection guide.
Typical applications
- Finishing
For more on cutting steel, see our material-specific guide.
Choosing the right TNGG 160404
Three things decide which variant you need:
- The workpiece material group. This page lists variants published for Steel, Stainless steel. Pick a grade from the group you are cutting — a steel grade on a superalloy will fail quickly.
- Feed, not depth of cut. The chipbreaker is defined by its feed window. Decide the feed first, then pick the geometry that covers it.
- Nose radius versus finish. TNGG 160404 is stocked here at 0.4 mm. A larger radius gives better finish at the same feed and a stronger edge, but raises cutting force.
Not sure whether TNGG 160404 is the right shape at all? The turning insert selection guide compares shapes by what the part profile allows.
Frequently asked questions about TNGG 160404
What size insert is TNGG 160404?
TNGG 160404 has an inscribed circle of 9.53 mm and a thickness of 4.76 mm. As a rule the depth of cut should stay under about two thirds of the inscribed circle.
What nose radius does TNGG 160404 have?
The nose radius (the last two digits of the designation) is 0.4 mm on the variants listed here. Surface roughness scales roughly with fn²/(32 × RE), so at a fixed feed a larger radius halves Ra.
Which holder does TNGG 160404 fit?
The holder designation must carry the same shape letter (T) and the same size digit. Send us your holder code and we will confirm the match before you order.
How many TNGG 160404 variants do you stock?
10 variants from Achteck, listed below with grade, chipbreaker and the published cutting data where the manufacturer provides it.
What cutting speed should I run for TNGG 160404?
For Steel, the published range across these variants is 50–200 m/min, with a typical window of 50–180 m/min. Heavy cuts sit at the bottom of that range, light finishing cuts at the top.